hort.net Seasonal photo, (c) 2006 Christopher P. Lindsey, All Rights Reserved: do not copy
articles | gallery of plants | blog | tech blog | plant profiles | patents | mailing lists | top stories | links | shorturl service | tom clothier's archive0
Gallery of Plants
Tech Blog
Plant Profiles
Mailing Lists
    Search ALL lists
    Search help
    Subscription info
Top Stories
sHORTurl service
Tom Clothier's Archive
 Top Stories
Disease could hit Britain's trees hard

Ten of the best snowdrop cultivars

Plant protein database helps identify plant gene functions

Dendroclimatologists record history through trees

Potato beetle could be thwarted through gene manipulation

Hawaii expands coffee farm quarantine

Study explains flower petal loss

Unauthorized use of a plant doesn't invalidate it's patent

RSS story archive

Re: [aroid-l] Artificial Trees

  • Subject: Re: [aroid-l] Artificial Trees
  • From: Harry Witmore harrywitmore@witmore.net
  • Date: Wed, 08 Jan 2003 18:26:32 -0500

Thanks Craig, the epiphyte displays at Faichild are exactly what I'm going for. They are very convincing. I will let you all know how it goes when I get started.

At 01:13 PM 1/8/2003 -0500, you wrote:
The following note is what I send out to people that ask about the construction of Fairchild Garden's epiphyte display. I have purchased my cork bundles from: OFE International, Inc., 305-253-7080; 12100 S.W. 129th Court, Miami, Florida 33186-6421

Epiphyte tree construction
A pipe frame is assembled from 4, 6, and 8 inch PVC irrigation pipe and fittings then covered by a skin of cork bark.

At the base of the tree is a concrete anchor with an embedded lag bolt. The tree base is bolted to this foundation and all the 1/4" stainless cable is clamped around the heavy bolt and threaded through the pipe and tied to the overhead beams. The stainless steel cable is actually the support structure, as the PVC is not strong enough to support itself.

The PVC pipe frame isn't glued but is screwed together using galvanized screws. I do it this way so that I can rotate the fittings or change the whole structure if the shape turns out to be unconvincing as a tree.

The cork bark covering is screwed on with galvanized deck screws, reinforced with steel washers under the screw heads. 'Liquid Nails' construction adhesive is spotted around the pipe to strengthen the corks bond to the frame. The washers spread the pressure on the cork to a wider area so that the screw will not go all the way through the soft cork. If the screws are noticeably visible after construction and planting, a dab of liquid nails and a cork chip covers the exposed metal, or even brown marker.

In my original structure, great attention was put to lining up furrows in the cork to help the believability of the branches, but that proved to be a waste of time after the plants were added.

After the large cork sections are attached, cut cork pieces are used to fill gaps between large slabs. Small gaps can be filled with cork chips, Osmumda fern fiber, or bits of moss. If a constructed tree is going to be heavily planted many of these small gaps shouldn't be visible any way.

The living epiphytic plants were attached using thin aluminum wire as a strap with small deck screws. Wire that is twisted around a screw then snuggly crosses the stem or rhizome and twists around the second screw. As you tightened the screws the wire tightens on the plant, holding most plants. Small plants can be attached with large ungalvanized electrical staples or even glued with the 'Liquid Nails'.

Most epiphytes readily attach to cork. I have had problems with cattleya orchids. I am not sure if the problem is an aversion to the cork, or staying too wet. Most show no root attachment to the cork bark.

...As far as how to make it look real... I just did it by intuition, but if you could see under the skin, there is just as much structure made from fittings as pipe. They make a number of fitting with 22% and 45% bends. Used lots of them to make your branches twist. Avoid long straight sections, even though it would lower costs. The fitting (example 8" connector with a 6" side tube at 22% angle) is the most expensive but the most important for looks. 8" for large trunks, down to 4" for smaller branches. Do not cantilever any branches over peoples heads more than 3' with out support. The PVC is not that strong, a heavy epiphyte load is heavy indeed.

I can't think of anything else except that after plants are attached all the areas that bother you tend to disappear. If you do a fallen branch as I did, try to keep most of the branches aiming in the same general direction as if it was from one side of the tree. I rearranged my first display when I was 1/2 way through because it wasn't looking natural.

Craig M. Allen
Conservatory Manager
Fairchild Tropical Garden
10901 Old Cutler Road
Coral Gables (Miami), FL 33156
Telephone: 305.667.1651, ext.3320
Fax: 305.667.6930
Email: callen@fairchildgarden.org
Web: www.fairchildgarden.org

-----Original Message-----
From: Harry Witmore [mailto:harrywitmore@witmore.net]
Sent: Tuesday, January 07, 2003 6:27 PM
To: aroid-l@lists.ncsu.edu
Subject: Re: [aroid-l] Artificial Trees

Wow, thanks for the responses so far. The article in the Orchids Magazine
mentioned the technique of using the expandable foam and then covering it
with cork bark. I would like to get a bale of cork. I have found some
sources for this in the past but I need to start looking again.

I don't have access to cypress but I do have red cedar and it's used around
here as fence post. I use it some to mount orchids and other small
epiphytes. This sounds like it could be a good on line web story. oh well
Brian has a wall, I have a tree, what else are you all dreaming of doing to
grow your plants in an attractive manner and if you are doing it already,
where are the picture. I think a page which shows members plant displays
would stir interest in the plants. Those of us in temperate to down right
frozen areas of the country, need to create the look of the tropics in our
own environment.

Any more ideas on this subject will be grateful.

Harry Witmore
Zone 7 NC
<http://www.witmore.net/>Cloud Jungle Art
<http://www.cloudjungle.com/eshop>Cloud Jungle ePiphytes
Harry Witmore
Zone 7 NC
<http://www.witmore.net/>Cloud Jungle Art
<http://www.cloudjungle.com/eshop>Cloud Jungle ePiphytes

 © 1995-2015 Mallorn Computing, Inc.All Rights Reserved.
Our Privacy Statement
Other Mailing lists | Author Index | Date Index | Subject Index | Thread Index